Spirax Sarco Steam Products

The Spirax Sarco BSA3T bellows sealed stop valve uses a carbon steel body and double bellows sealing for dependable shut-off and limited throttling duties in higher-pressure steam, condensate and industrial fluid systems.

BPC32YCV is part of the Spirax Sarco BPC32 carbon steel balanced pressure thermostatic steam trap family. This page brings together the main BPC32 technical document, the installation and maintenance guide that explicitly covers BPC32YCV, and a direct route for replacement checks.

The AVC32 is a maintainable carbon steel balanced-pressure thermostatic air vent for removing air and other non-condensable gases from higher-pressure steam mains and high points on steam equipment.

The Spirax Sarco LP30 self-monitoring level probe is a high-integrity level sensor for steam boilers with built-in self-diagnostics, triggering low-level alarms or safety interlock actions to protect boiler operation.

The Spirax Sarco CP30 conductivity probe measures boiler water conductivity or TDS for steam boiler blowdown monitoring and control systems.

The Spirax Sarco TD32F flanged thermodynamic steam trap is a maintainable medium-pressure disc trap with an integral strainer for PN40 flanged steam systems requiring DN15-DN25 selection.

The Spirax Sarco BC3150 boiler blowdown controller monitors boiler water TDS and controls the blowdown valve for continuous dissolved-solids management in steam boiler applications.

The AV13 is a maintainable brass balanced-pressure thermostatic air vent for removing air and other non-condensable gases from steam mains and high points on steam equipment.

The Spirax Sarco BC3250 boiler blowdown controller monitors boiler water TDS and automates blowdown control, bottom blowdown timing, retransmission and communications for steam boiler applications.

Spirax Sarco CSF16 steam filters help remove contaminant particles from clean steam lines where steam quality, product contact and hygienic hardware protection matter.

The Spirax Sarco MFP14 condensate pump is a steam- or compressed-air-powered automatic pump for lifting hot condensate and other liquids where low differential pressure, backpressure or vacuum prevent normal drainage.

The Spirax Sarco TD52 thermodynamic steam trap route covers the maintainable stainless steel TD52M family for steam mains and other smaller-condensate duties, including LC low-capacity and anti-air-binding variants.

The Spirax Sarco APT14 automatic pump-trap combines steam trapping and pressure-powered condensate pumping in one unit for stalled heat exchangers, backpressure and vacuum condensate duties.

The Spirax Sarco FTGS14 ball float steam trap provides continuous condensate drainage, integral automatic air venting and documented threaded or flanged routes for steam duties that need stable heat-transfer performance.

The Spirax Sarco EP5 is a traditional electro-pneumatic valve positioner accepting 4-20 mA current or 0.2-1.0 bar pneumatic signals for single-acting linear pneumatic actuators in general-purpose industrial valve positioning applications.

The Spirax Sarco EP500 is a standard electro-pneumatic positioner with 4-20 mA input, split-range capability, integral pressure gauges and IP65 protection for linear and rotary pneumatic control valves.

The Spirax Sarco SP500 is an enhanced loop-powered electro-pneumatic smart positioner with optional HART communication, diagnostic data logging and auto commissioning for linear and rotary pneumatic valves.

The Spirax Sarco SX80 is a 1/16 DIN panel mount process controller with universal input, universal output, PID auto-tuning, 3 setpoints and a 5-character quick code for fast configuration.

The Spirax Sarco MST21 is a maintainable stainless steel balanced pressure thermostatic steam trap designed for tracing lines and small condensate discharge duties, with STD, SUB and NTS bellows options.

The Spirax Sarco SP400 is a loop-powered valve positioner for linear and 90 degree rotary pneumatic valves, using a 4-20 mA input signal to control valve position.

Spirax Sarco SP7-10, SP7-11 and SP7-12 smart positioners control pneumatic linear or rotary actuators and support 4-20 mA, HART, PROFIBUS PA or Foundation Fieldbus communication routes.

The Spirax Sarco DP27 is a pilot-operated ductile iron pressure reducing valve for steam, compressed air and selected industrial gas duties.

The Spirax Sarco FT43 ball float steam trap is a cast iron flanged trap route for continuous condensate drainage, integral automatic air venting and FT43-10 or adjacent FT43 selection enquiries.

The Spirax Sarco DCV3 disc check valve is a stainless steel wafer non-return valve for steam, condensate, hot water and process pipework where compact reverse-flow protection is required.

The Spirax Sarco FT14 ball float steam trap provides continuous condensate drainage, integral automatic air venting and documented threaded or flanged routes for steam duties that need stable heat-transfer performance.

The Spirax Sarco SV607DS Safety Valve is treated here as an order-code level model within the documented SV607 flanged full-lift safety valve platform for steam, inert gas and water overpressure protection.

The Spirax Sarco BRV2S is a compact direct acting pressure reducing valve for steam and compressed air duties, with ductile iron construction, screwed or flanged connections and documented spring-selected outlet pressure ranges.

The Spirax Sarco 25P pressure reducing valve is a pilot-operated steam pressure reducing valve route for users who need a direct product path beyond the wider regulator family page.

The Spirax Sarco BSA2T bellows sealed stop valve uses a ductile iron body and double bellows sealing for dependable shut-off and limited throttling duties in steam, condensate and industrial fluid systems.

Spirax Sarco BTM7 clean steam traps provide maintainable 316L thermostatic condensate drainage for hygienic steam systems used on sterilisers, SIP lines and process vessels.

Spirax Sarco CS10 clean steam separators remove entrained moisture from clean and pure steam systems to improve steam dryness and protect sterilisation and hygienic process performance.

Spirax Sarco SRV66 sanitary pressure reducing valves provide stable downstream pressure in clean steam, water and inert gas systems with self-draining hygienic construction and compact installation.

Spirax Sarco blowdown vessels collect high-temperature boiler blowdown water and help discharge it more safely in line with site health, safety and environmental requirements.

Spirax Sarco bottom blowdown systems remove sludge and suspended solids from the base of steam boilers to support steam quality, boiler efficiency and repeatable blowdown practice.

Use Spirax Sarco conductivity meters to measure conductivity in boiler water, feedwater and condensate, supporting TDS control and clearer boiler water quality management.

Spirax Sarco feedtanks act as atmospheric deaerators that mix make-up water, condensate and flash steam to improve feedwater condition and reduce boiler operating cost.

Spirax Sarco boiler blowdown heat recovery systems recover flash steam and hot water value to reduce make-up water demand, chemical cost and avoidable energy loss.

Spirax Sarco boiler water sample coolers help operators take safe, representative samples without flash steam affecting sampling accuracy.

Spirax Sarco steam injectors heat boiler feedwater by direct steam injection in feedtanks, helping improve deaeration and reduce water treatment chemical demand.

Spirax Sarco boiler house vent heads separate condensate and discharge dry steam safely to atmosphere at low velocity with minimal maintenance.

Spirax Sarco AVM7 thermostatic air vents remove air and other non-condensable gases from clean steam systems to improve warm-up, heat transfer and steam quality.

The Spirax Sarco BT6-B balanced-pressure thermostatic steam trap uses hygienic 316L construction, minimal condensate retention and near-saturation discharge for clean steam duties.

Spirax Sarco clean steam generators produce clean steam from purified or deionised water for sterilisation, humidification and other high-integrity hygienic process duties.

Spirax Sarco FTS14 ball float steam traps provide continuous condensate drainage at steam temperature with integral air venting for stainless steel and hygienic steam duties.

Spirax Sarco M70i and M80i sanitary ball valves use hygienic true-port 316L construction for high-purity shut-off duties in clean steam and process utility systems.

Spirax Sarco STERI-TROL clean service control valves combine hygienic design, drainability and modulating or on-off control for clean steam and clean process duties.

Spirax Sarco SVL488 clean service safety valves provide hygienic overpressure protection for pure steam, clean steam and inert gas systems used in clean-service applications.

Spirax Sarco compressed air drain traps and ancillaries remove liquid from pressurised air and gas systems while helping prevent unnecessary gas loss.

Spirax Sarco electrical condensate recovery pumps return larger volumes of hot condensate for boiler feedwater or process reuse, improving steam system efficiency.

Spirax Sarco control valves combine modular trim, actuator and positioner options for steam and industrial fluid control duties.

Spirax Sarco desuperheaters reduce superheated steam temperature with controlled water injection for safer downstream process and heat transfer duties.

Spirax Sarco electric actuators provide accurate remote valve actuation, self-commissioning and diagnostics for steam and industrial control duties.

Spirax Sarco pneumatic actuators provide accurate, air-powered valve actuation for steam and industrial control duties across a wide range of differential pressures.

Spirax Sarco self-acting temperature controls deliver reliable steam temperature control without electricity or compressed air.

Spirax Sarco flow computers, indicators and transmitters support accurate steam, gas and liquid measurement with mass flow, energy and signal integration capability.

Spirax Sarco Gilflo and ILVA flowmeters provide variable-area flow measurement for steam, gas and liquids with wide turndown and strong low-flow visibility.

Spirax Sarco TFA saturated steam flowmeters provide compact steam metering for smaller line sizes with practical installation and energy visibility benefits.

Spirax Sarco TVA flowmeters provide compact steam flow measurement with density compensation and stronger visibility across changing steam loads.

Spirax Sarco steam heat exchangers and packaged heat transfer solutions provide efficient indirect heating for industrial and building services duties.

Spirax Sarco steam jet thermocompressors recover low-pressure or flash steam so it can be reused more effectively in the process.

Spirax Sarco steam injection humidifiers use low-velocity steam distribution to improve humidification quality, steam-air mixing and duct performance.

Reliable isolation ball valves designed to reduce maintenance time and support safer steam system operation.

Spirax Sarco HV3 stop valves provide robust manual shut-off for steam and condensate duties where straightforward isolation and low maintenance matter.

Spirax Sarco depressurisation valves provide controlled blowdown and discharge handling for steam systems where safer pressure release and operator protection matter.

Spirax Sarco diffusers help reduce blowdown noise by up to 80% and create a safer atmospheric discharge from steam traps, vents and blowdown points.

Spirax Sarco hosedown stations mix steam and water to provide instantaneous hot water for washdown, cleaning and sanitation duties.

Spirax Sarco pressure and temperature gauges provide clear local indication for steam systems, helping operators verify conditions and troubleshoot faster.

Spirax Sarco separators remove entrained moisture from steam, compressed air and gas systems to improve dryness, protect equipment and support process quality.

Spirax Sarco sight glasses provide visual confirmation of flow, leakage and line condition to help operators troubleshoot steam systems faster.

Spirax Sarco strainers and filters remove solid contamination from steam systems to protect downstream valves, traps and control equipment while reducing maintenance.

Spirax Sarco vacuum breakers protect steam systems and vessels from damaging vacuum conditions that develop during cooling, shutdown or condensate collapse.

Spirax Sarco bimetallic steam traps provide durable thermostatic drainage for applications where sub-cooled discharge, sensible heat recovery and rugged performance matter.

Spirax Sarco fixed temperature discharge steam traps use liquid expansion operation to release condensate at a preset temperature in specialist thermostatic duties.

Spirax Sarco inverted bucket steam traps provide robust mechanical condensate drainage for demanding steam duties where reliability and long service life are priorities.

Spirax Sarco manifolds and insulation jackets help simplify steam tracing layouts, centralise distribution and collection points, and reduce heat loss.

Spirax Sarco sealed steam traps use compact all-welded construction to reduce steam leakage risk, simplify replacement and lower maintenance effort.

Spirax Sarco swivel connectors and traps help standardise steam trap installation, shorten replacement time and reduce leak paths around the trap station.